![]() ![]() The QCM electronics is designed as a shield for Arduino Micro microcontroller board. It is designed to minimize the electric power consumption. The QCM circuit consists of a quartz crystal oscillator driver, signal conditioning circuit and a new I2C temperature sensor with extended T range (-40☌ to +125☌), which improves the signal quality of the crystal oscillator. The electronic circuit is optimized for use in crystal oscillator applications for quartz sensors at 10 MHz and also in the range of frequencies, from 1 MHz to 6 MHz. The QCM shield is a dual layer PCB characterized by lead-free gold-plated pads. Here’s a another blog post that you can read that it is dedicated to Arduino modules: “ 21 Arduino Modules You Can Buy For Less Than $2“.The QCM electronics is a high-quality Arduino compatible shield for quartz crystal microbalance applications. Share this post with a friend that also likes electronics. This Shield includes an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for transparent wireless serial connection setup.Īre you thinking about ordering one of theses Shields listed above? Or are you thinking about doing a project with one of these? It can lower the MCU’s demand on software, which makes it a perfect solution for embeded applications of low-cost, low-power consumption MCU.ĮSP8266 Wi-Fi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or Wi-Fi related projects. This Shield is a well-equipped network processing unit that can simplify the network connecting process. The Wireless SD Shield allows the Arduino to communicate wirelessly using a wireless module. The GPS Logger Shield comes with a GPS module and is designed to log data to an SD card. It uses I2C interface for the sensor configuration and SPI interface for camera commands and data stream. With this Shield it is possible to reduce the complexity of the camera control interface. 25 Useful Arduino Shields That You Might Need to Get Relay shield protoshield motor shield capacitive touchpad shield can-bus shield smoke detector shield. The MP3 Player Shield provides a simple way to add sound effects or music to your projects. With this shield from Adafruit, you can control a 5×8 matrix of RGB LEDs using only one pin. It can read and write tags so, it is perfect to use for RFID-tag projects. This Shield is perfect for any 13.56MHz RFID or NFC application. The microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. It has plugs for a VGA monitor and stereo speakers. This Shield is a game adapter for Arduino or anything with an SPI interface. It allows you to dial a phone number or send a text message to a friend via easy to use AT commands. The GSM/GPRS Shield allows you to connect your Arduino to GSM/GPRS cell phone network. The joystick Shield provides simple analog inputs and four separate buttons and one button under the joystick itself. Some cool projects with this shield include musical intruments, cool computer interfaces, etc. With this Shield you can connect up to 64 buttons to your Arduino. The CISECO ProtoX Shield is a Prototyping board with SMT pads and serial breakout. With this shield, it is possible to add high quality audio to your projects. Audio files are read off of an SD/MMC card. It can play up to 22KHZ, 12 bit uncompressed audio files of any length. This Shield solves many problems related to audio low quality with electronic projects with audio. It is useful if you need negative voltage. This shield generates negative voltage for Arduino. This Shield can detect concentrations of combustible gas in the air and read it as an analogue value. The CAN – BUS Shield adopts MCP2515 CAN bus controller with SPI interface and MCP2551 CAN transceiver to give CAN – BUS capibility to the Arduino. ![]() ![]() The Touchpad Shield allows you to build simple capacitive touch interfaces. With this, it is possible to control a 16×2 Character LCD, up to 3 backlight pins and 5 keypad pins using only the two I2C pins on the Arduino. This Shield makes it easy to use a 16×2 Character LCD. It makes it easy to incorporate a motor into any of your projects. This Shield allows an easy control of motor direction and speed. It allows for easy connections between the breadboard and the Arduino. The ProtoShield is a prototyping Shield that makes it easy to prototype. The Relay Shield is a module with 4 mechanical relays that provides you an easy way to control high voltage. You just have to plug the shield onto the Arduino board and then, connect it to your network. The Ethernet Shield allows you to connect your Arduino to the internet. I’ve also wrote a list of 21 modules that you can buy for your Arduino for less than $2. You just need to plug them over the top of the Arduino board. There are countless types of shields to do countless tasks. Arduino shields are boards that will expand the functionalities of your Arduino. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |